Close
|
|
|
|
A hot topic question that the ASK I-CAR team has been repeatedly asked, “Does Ford have an approved sectioning procedure for the outer quarter panel that does not require the removal of the roof panel?” We now have the answer!
The collision repair industry is ever-changing. In an average year, there are over a hundred new models, face-lifts, and redesigns. With all of these changes, it can be difficult to keep up with all the makes, models, and new technologies. Luckily, I-CAR’s RTS team is dedicated to keeping track of these changes and locating where to find this new information. In 2016 we have added several features and improvements to the RTS portal to make this this ever-changing information easier to find. Let’s take a look.
Nissan released a new position statement addressing the repairability of a damaged rear bumper cover on vehicles equipped with Blind Spot Warning (BSW). Let’s take a look at what is included in this position statement.
Weld-through primers are generally a zinc-based product that are applied to the mating surfaces prior to welding. Corroding zinc forms zinc oxide which protects the steel. This is called sacrificial corrosion. For a quality weld to be made it’s required that the weld-through primer be removed from the direct weld zone before welding the joint when GMA welding. Many OEMs have a position on when and how to use weld-through primer or when it shouldn’t be utilized. Let’s see what Mazda recommends and where this information can be found.
When a damaged vehicle enters a collision repair facility, many times the repairs require the battery to be disconnected. Operations such as welding, SRS repairs, engine work, and body panels being open for extended periods of time, can all require that the battery be disconnected. At one time the radio presets would be written down before the battery was disconnected and programmed after the battery was reconnected. However, today many OEMs have special precautions or steps that need to be taken when disconnecting the battery. Let’s take a look at what some OEMs require when disconnecting the battery.
Weld-through primers are generally a zinc-based product that are applied to the mating surfaces prior to welding. Corroding zinc forms zinc oxide which protects the steel. This is called sacrificial corrosion. For a quality weld to be made it’s required that the weld-through primer be removed from the direct weld zone before welding the joint when GMA welding. Many OEMs have a position on when and how to use weld-through primer or when it shouldn’t be utilized. Let’s see what Toyota/Lexus/Scion recommends and where this information can be found.
Now that the new year is well underway, let’s take a look at some of your favorite things from 2016. Let's continue with your favorite questions.
Now that the new year is well underway, let’s take a look at some of your favorite things from 2016. Let's start with your favorite articles.
Weld-through primers are generally a zinc-based product that are applied to the mating surfaces prior to welding. Corroding zinc forms zinc oxide which protects the steel. This is called sacrificial corrosion. For a quality weld to be made it’s required that the weld-through primer be removed from the direct weld zone before welding the joint when GMA welding. Many OEMs have a position on when and how to use weld-through primer or when it shouldn’t be utilized. Let’s see what Kia recommends and where this information can be found.
Today, most people in the collision industry have heard at least something about Advanced Driver Assistance Systems (ADAS). ADAS normally requires special treatment during a collision repair, such as calibration. You may think that you don’t have to be too concerned about these systems because it’s only on really high end vehicles. But, that’s not the case. A recent document released by WardsAuto tells us just how common ADAS is on new vehicles.
Weld-through primers are generally a zinc-based product that are applied to the mating surfaces prior to welding. Corroding zinc forms zinc oxide which protects the steel. This is called sacrificial corrosion. For a quality weld to be made it’s required that the weld-through primer be removed from the direct weld zone before welding the joint when GMA welding. Many OEMs have a position on when and how to use weld-through primer or when it shouldn’t be utilized. Let’s see what Jaguar Land Rover (JLR) recommends and where this information can be found.
Accessing the body repair manual before performing a repair has become increasingly critical. Ask I-CAR has received an inquiry, “I can’t find the sectioning procedure for the front lower rail on the 2016 Chevrolet Malibu? We’ve sectioned the front lower rail on Malibu’s in the past?” After researching the repair information, we found the answer. Let’s take a look at what was found.
Weld-through primers are generally a zinc-based product that are applied to the mating surfaces prior to welding. Corroding zinc forms zinc oxide which protects the steel. This is called sacrificial corrosion. For a quality weld to be made it’s required that the weld-through primer be removed from the direct weld zone before welding the joint when GMA welding. Many OEMs have a position on when and how to use weld-through primer or when it shouldn’t be utilized. Let’s see what Ford/Lincoln recommends and where this information can be found.
The windshield helps to manage collision energy and has become an integral part of several advanced safety systems. Many vehicle makers offer stationary glass replacement information and approved products for their vehicles. The vehicle makers have many different materials and recommendations; we have gathered this information into one location to help ensure complete, safe and quality repairs.
When advanced driver assistance systems (ADAS) are replaced after an accident, there may be some fine print that you don’t want to overlook. BMW/Mini has some interesting requirements after the KAFAS or forward facing camera is replaced, that the customer needs to be aware of.
